MEP Engineering Services

Approx. Rs 1,500 / PieceGet Latest Price

Service Details:

1. Electrical Conduit and Conduit Fitting

Electrical Conduit is a tube that carries electrical wire for power or communications. Conduit is made in rigid steel; lighter steel called IMC or intermediate conduit; EMT or thin wall conduit; PVC or plastic; aluminum; or PVC coated; which is rigid covered with 40 mil PVC jacket. Conduit for electrical ranges in sizes from 3/8″ to 6″.

 

2. Electrical Wire and Cable

Electrical Wire is drawn metal, copper or aluminum that carries electricity through an electrical circuit. Wire may be run overhead, under ground, through conduit or flex or open. Wire is protected by design with a jacket depending on usage. It can also be flexible as in the use of extension cords. It can be very small in size as 26 gauge to as large as 2000 MCM.

 

3. Explosion Proof Enclosures

Explosion Proof is a product design to contain an electrical short so that it doesn’t ignite a hazardous atmosphere causing an explosion. Refineries, gas stations, paint booths are examples of where these products would be used. They are heavy duty steel or aluminum by design, or can be fiberglass as well.

 

4. Circuit Breakers

Circuit Breakers are devices that automatically interrupt the follow of an electric current to protect against a short or overload. Circuit Breakers are made by several manufacturers including Cutler Hammer/ Westinghouse, General Electric, Square D, ITE Sieonans, and Federal Pacific. Circuit Breakers protect the smallest house circuit to the largest industrial requirements.

 

5. Electrical Connectors

Electrical Connector is a part that will join or adapt one part to another. Connector range in size from 3/8″ to 6″. They can be indoor, outdoor, corrosive protected or explosion proof.

 

6. Electrical Box

Electrical Box is an enclosure used for many purposes such as pulling, connecting or terminated an electrical circuit. Electrical box can be set screw or indoor; it can be rain tight, or outdoor. They can be made of steel, aluminum, plastic, stainless steel, or cast iron. Requirement can include corrosive protected or explosion protected by design.

 

7. Lugs

Lugs are the electrical connectors that terminate the electrical circuit. Lugs are made of copper, aluminum, or bronze. They are made for the smallest wire size, 26 gauge to the largest 2000 MCM. Lugs can be mechanical or set screw; compression or crimp, solder or weld; or clamp type. T&B, Burndy, Penn Union, Panduit, and 3M are some different manufacturers of lugs.

 

8. Motor Control

Motor Control is an apparatus used to regulate a motor or mechanism. It can control the smallest mechanism to the largest power turbines. There are several manufacturers of motor control including Allen Bradley, Square D, Cutler Hammer, ITE Siemens, General Electric and Westinghouse.

Approx. Rs 500 / PieceGet Latest Price

Service Details:

There are various types of parts available in plumbing systems. It’s important to know what these parts are and learn about each one’s important role and function. Let’s take a look at these important plumbing parts and terminology.

BYPASS VALVE

Bypass valves play the role of controlling pressure in a plumbing system by diverting part of the water flow. This normally happens by bypassing water from the pump outlet back into the reservoir. Bypass valves essentially regulate the pressure in a plumbing system by opening just enough to relieve pressure on the inlet port. Perfect pressure means perfect water flow.

ISOLATION VALVE

Isolation valves allow you to turn off the water supply to a particular feed or faucet without having to turn off the mains. These valves are often attached to faucets under sinks in what looks like a slot headed screw. The valve in open when the slot is parallel to the arrow sign on the valve. When the slot is turned, it closes the valve and stops the water flow. Isolation valves are handy for issues such as leaking faucets, when a specific area needs to be isolated.

PRESSURE BALANCE CARTRIDGE

These cartridges or valves help to supply water at a constant pressure to a shower or bathtub despite pressure fluctuations from supply lines. They work by measuring the volume ratio of hot water to cold water and adjust these volumes continually to maintain a constant pressure.

THERMOSTATIC SHOWER VALVE

Thermostatic valves operate by sensing the actual temperature of the incoming water and then adjusting the hot and cold flow accordingly to maintain a constant temperature.

FLUSH VALVE

The flush valve is the part inside the toilet that moves the water from the holding tank into the bowl. As you push the toilet handle down, the valve lifts to allow the water through. Flush valves come in different sizes depending on your personal requirements.

FILL VALVE

The fill valve is a very important part of a standard toilet. It manages the water that fills into the holding tank. The valve does this by opening the water flow as the toilet is flushing, and closes off the water supply when the tank has been refilled.

FLANGE

A flange provides for the connecting pipes, valves or pumps to form a piping system. Flanges are connector pieces that are either welded or screwed on to form a joint. Flanged joints are assembled by bolting two flange pieces together with a gasket in between which provides a seal.

COUPLING

Providing a similar function to a flange, a coupling is a very short length or pipe with a socket at either one or both ends. Couplings allow for pipes or tubes to be joined together to make up a plumbing piping system.

SUPPLY LINE

A supply line is a plastic or metal line that supplies water from the main line to an individual fixture such as a faucet or toilet.

ROOTER

A Rooter is another name for a drain cleaning machine. This name originated from the function of clearing tree roots from sewer pipes. Various rooters can be used for many different drain blockages.

TRAPS

A trap is a curved section of drain line that prevents sewer odors from escaping. These are really important in order to prevent bad odors and hygiene issues. Drain fixtures require a “P” trap, while toilets require an “S” trap. Trap adapters are used to connect trap arms to piping.

SEDIMENT FILTER

Water can contain various levels of sediment. Although sediment often goes unnoticed, over time sediment build up can result in a layer of sediment being deposited in your plumbing system which could contribute towards a drain blockage. Sediment filters prevent sediment particles from entering the plumbing system thereby eliminating any sediment deposit

Approx. Rs 35,000 / PieceGet Latest Price

Service Details:

Switchgear is a broad term that describes a wide variety of switching devices that all fulfill a common need: controlling, protecting, and isolating power systems. Although this definition may be extended to include devices to regulate and meter a power system, circuit breakers, and similar technology.

Approx. Rs 1,00,000 / sq ftGet Latest Price

Service Details:

We, Proximity Engineering are one of the popular Manufacturer, Trader and Service Provider of Air Pollution Control System, HVAC AMC Service, Fabrication Work, HVAC Systems and many more. These offered services are reliable and promptly executed by our sharp minded professionals. In addition to this, our team members work in close connection to impart these services as per our patrons’ specific needs and requirements.

Approx. Rs 45,000 / PieceGet Latest Price

Service Details:

Heat Pump is an efficient technology using heat source from ambient air. Heat Pump can generate large thermal energy with little electric energy.

Approx. Rs 15,100 / PieceGet Latest Price

Service Details:

Three Phase Distribution Transformers is called as distribution system. Generally, a distribution system is the electrical system between the substation fed by transmission system and the consumer's meters